Stands for American Iron and Steel Institute. The institute serves as the voice of the North American steel industry. AISI numbers are used to categorize metals by alloy type and carbon content, and they do it with four digits. The first two digits of an AISI number refer to the alloy type, and the second two digits refer to carbon content.
A metal made by combining two or more metallic elements. An alloy typically possesses qualities different from those of the components used to create it.
Stands for American Society for Metals. ASM International is the world’s largest association of metal material engineers and scientists. The association engages and connects materials professionals and their organizations to the resources necessary to solve problems, improve outcomes, and advance society.
Stands for American Society for Testing and Materials. ASTM International is a not-for-profit organization that develops standards for materials, products, systems, and services. Metal with an ASTM designation meets the international standards for quality and regulations.
This process levels coil into a flat sheet or blank. The service provides better length and width tolerances than sheared product, and it can improve diagonal tolerances as well.
Cutting metals can leave behind burrs, which are unwanted raised edges or protrusions. Deburring is the process of removing these burrs with a tool.
Drawing is a metalworking process that uses tensile forces to stretch metal. As the metal is drawn, it stretches thinner, into a desired shape and thickness.
Drawing is usually done at room temperature, classifying it as a cold working process. However, it may be performed at elevated temperatures during special applications like on large wires, rods, or hollow sections in order to reduce forces.
A metal fabricating term that refers to the degree to which a material can be bent, stretched, or compressed before rupturing. A metal’s elongation is a point between tensile strength and yield strength, and it is typically expressed as a percentage of the original length.
The thickness of sheet metal in the USA is commonly specified by a traditional, non-linear measure known as its gauge. The larger the gauge number, the thinner the metal.
A heat number is an identification number that is stamped on a material plate to prove it meets industry quality standards which require materials to be tested by the manufacturer. The heat lot or heat number is used to identify production runs for quality control purposes.
Edge rolling is the process of adding finishing edges to metal. It forms the edge of a strip to the desired shape beyond that of a standard slit edge.
Stands for Military Standard. This classification establishes uniform engineering and technical requirements for military-unique or substantially modified commercial processes, procedures, practices, and methods. In order to qualify, materials have undergone rugged, exact testing, equal to the exigencies of combat use.
Normalization is a heat treatment that relieves stress on steel to improve ductility and toughness in steel that may harden after the cold working process. During normalization, steel is warmed to a temperature just above its upper critical point. Normalized heat treatment facilitates a more uniform final product.
The Rockwell Scale indicates the hardness of materials. Rockwell hardness numbers are most often used to describe the hardness of metals, although they are also used for some plastics. The Rockwell scale is based on measuring the depth of the indentation made by pressing a diamond point into a material.
Jinxinda Product Page
Stands for Society of Automotive Engineers. SAE International is a global association of engineers and related technical experts in the aerospace, automotive, and commercial-vehicle industries. Materials meeting SAE standards are internationally recognized for safety, quality, and effectiveness.
Slitting is a precise shearing process, but instead of making cuts at the end of a workpiece like shearing, slitting cuts a wide coil of metal into a number of narrower coils as the main coil is moved through the slitter. During the slitting process, the metal coil passes lengthwise through the slitter’s circular blades.
Temper refers to reheating hardened, normalized, or mechanically worked steel to a temperature below the critical range to soften it and improve impact strength. Tempering results in greater toughness by decreasing an alloy’s hardness.
The maximum stress a material will withstand before fracturing or breaking. The ultimate tensile strength is calculated from the maximum load applied during the test, divided by the original cross-sectional area.
Stands for the Unified Numbering System for Metals and Alloys. UNS designation provides a means of correlating internationally used metal and alloy numbering systems currently administered by societies, trade associations, and those individual users and producers of metals and alloys. This system is meant to avoid the confusion caused by using more than one identification number for the same metal or alloy, and the opposite situation of having the same number assigned to two or more different metals or alloys.
The amount of stress a material can withstand before causing permanent deformity.
Today, it has been diversified in terms of types with distinct characteristics. Construction steel coils are an indispensable material for every project. For detailed information about construction steel coils and where to buy genuine coils, find out with MRS Steel through the article below.
Construction steel coils are a type of steel material produced for construction work and are a raw material for heavy industry. Construction steel coils are wire, coiled, smooth, or ribbed, and have a common diameter of 6mm, 8mm, 12 mm, or 14mm.
Construction steel coils usually have characteristics such as high strength and good load capacity. Steel is the material that creates solidity for the structure of a building. However, not all types of steel meet the requirements to be used in the construction process. Steel must ensure the elements of hardness and elasticity, not warping. It is these characteristics that make steel an important material for ease of construction and later replacement.
The production process of construction steel coils is quite complicated and requires high technology. After the steel is refined, the raw material is cast into a billet, and the ingot continues to melt to form a rolled steel product.
Steel coil is one of the most important construction steels, commonly used in construction works such as concrete pouring, reinforcement for industrial and civil buildings, buildings, highways,... The following are the common types of construction steel coils on the market today:
Construction steel coils Ф6: It is known as a construction coil with a steel diameter of (d6) = 6mm. This is a type of steel used for concrete reinforcement manufactured according to Vietnamese standards TCVN -1:.
Construction steel coils Ф8: It is a construction steel coils, also known as a D8 coil, with a cross-sectional diameter of 8mm. This is one of the most commonly used steels on the market today.
Construction steel coils Ф8 barbed: As a product with a measured cross-sectional length of steel rods with D = 8mm, they are capable of withstanding high temperatures without rusting in humid environments or at abnormal temperatures.
Construction steel coils Ф10: It is D10 steel coil; this is a 10mm diameter coil of steel, commonly used in reinforced concrete structures to make the foundation of civil houses, beams, and pouring reinforced concrete in large-scale construction projects. as large as industrial parks, factories,...
If you want to learn more, please visit our website industrial hot rolled steel coil.