DIN EN857 2SC hydraulic hose is a compact, high-pressure hose construction reinforced with two braided steel-wire layers. It is commonly selected for hydraulic circuits where a flexible connection, a relatively small outside diameter, and pressure resistance are needed. The correct choice depends on the hose size, working pressure, temperature, fluid, routing, and end connections—not on the “2SC” designation alone. This guide explains the construction, typical applications, specification checks, and purchasing questions to help you evaluate a hose before requesting a quotation.
Please visit our website for more information on this topic.
This guide is intended for hydraulic equipment manufacturers, maintenance teams, distributors, and industrial procurement professionals evaluating DIN EN857 2SC hoses. It is useful when replacing an existing hose, specifying a new hydraulic line, or comparing suppliers for a recurring purchase. It can also help buyers prepare the technical information needed for a more accurate quotation. Final selection should be checked against the equipment manufacturer’s requirements and the selected product’s documentation.
A DIN EN857 2SC hose is a flexible assembly component designed to convey hydraulic fluid under pressure. A typical construction includes an oil-resistant synthetic-rubber inner tube, two braided steel-wire reinforcement layers, and a synthetic-rubber outer cover. The inner tube contacts the fluid, the reinforcement carries pressure loads, and the cover helps protect the hose from its working environment.
The “2” in 2SC refers to two wire-braid reinforcement layers, while “SC” identifies the compact hose type in the EN 857 designation. Compact construction can help when installation space is limited, but it does not eliminate the need to check the hose’s actual outside diameter and minimum bend radius. These dimensions vary with nominal bore and product design. Request the dimensional data for the exact size you intend to use.
Many commercial DIN EN857 2SC product ranges cover nominal bores from about 5 mm to 25 mm. This is a common catalogue range rather than a guarantee that every supplier offers every size. Working pressure is size-dependent, so buyers should use the manufacturer’s rating for the selected bore rather than assume one pressure applies to the full range. Burst pressure, test conditions, and safety factors should likewise come from the relevant product documentation.
A commonly listed temperature range for 2SC hoses is approximately -40°C to +100°C. Actual suitability may change with the fluid, duty cycle, ambient conditions, and hose construction, so confirm the limits for the specific product. Also check fluid compatibility, cover resistance, impulse-duty requirements, and the permitted bend radius. These details matter because a hose that matches the nominal standard may still be unsuitable for a particular installation.
Buyers commonly evaluate 2SC hoses for hydraulic lines on construction and agricultural machinery, industrial equipment, material-handling systems, and mobile machinery. Their compact construction can be useful where routing space is restricted or a smaller hose profile is preferred. Typical duties include pressure lines and other hydraulic connections, subject to the selected hose’s pressure and application ratings. The equipment manufacturer’s specifications should take priority where they identify a required hose type or assembly.
If you are looking for more details, kindly visit Hengshui Xinchi Hose Manufacturing Co., Ltd..
Application matching starts with operating conditions, not a broad equipment category. Record the hydraulic fluid, normal and peak pressure, temperature range, movement or vibration, and exposure to abrasion, weather, or chemicals. Note whether the line is static or flexes during operation, and identify any tight bends or installation constraints. This information helps distinguish a suitable 2SC option from a hose with a different construction or rating.
A frequent mistake is selecting by nominal bore and working pressure alone. That approach can overlook bend radius, temperature limits, fluid compatibility, or the fitting connection. Another error is assuming every product described as “2SC” has identical dimensions or performance. Compare the current datasheets for the actual products under consideration and ask the supplier to clarify any difference.
Buyers should also avoid relying only on a sample appearance or a previous order description. Product revisions, fitting combinations, and application conditions can change, so retain the full specification for each purchase. If a hose is being replaced, record its markings and assembly details where available, but verify them against the machine requirements. Do not install a hose if its rating or compatibility cannot be confirmed.
Pricing for a 2SC hose or completed assembly depends on factors such as bore, length, fitting type, order quantity, packaging, and requested documentation. A quote for hose-only supply may not be comparable with a quote that includes crimped fittings or protective components. Minimum order quantities and production or shipping lead times vary by supplier, product configuration, and stock position. Ask suppliers to state these terms in the quotation rather than assume a standard MOQ or delivery schedule.
For an efficient quotation, provide the standard, size, required quantity, working conditions, assembly length, fitting details, destination, and any packaging or document requirements. If you do not have every detail, share a drawing, sample, or equipment specification for review. Ask which items are confirmed and which remain subject to technical approval. This makes supplier comparisons more meaningful and reduces the risk of ordering a hose that does not fit the application.
Hengshui Xinchi Hose Manufacturing Co., Ltd. supplies hydraulic rubber hose products and can discuss DIN EN857 2SC requirements with B2B buyers. For a product evaluation, share the requested size, operating conditions, fitting information, quantity, and destination. We can then review the details needed for a suitable quotation and identify any information that should be confirmed before production or shipment. Final compatibility and installation approval remain subject to the application requirements and the selected product documentation.
DIN EN857 2SC is a compact, two-steel-wire-braid hydraulic hose construction commonly considered for pressure lines where routing space and flexibility matter. It is not enough to choose by standard name alone: confirm bore, working pressure, temperature, fluid compatibility, bend radius, cover conditions, and fittings for the exact product. Compare supplier quotations using the same technical and commercial requirements. To begin an evaluation with Hengshui Xinchi Hose Manufacturing Co., Ltd., send your application details and requested configuration for review.
The company is the world’s best DIN EN857 2SC Hydraulic Hoses supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.